LED Energy saving products

Home | how to cut the LED Strips | LED light Strip in Canopy | LED Dome light installation | LED Worklight DIY
Facts about LEDs | GU10 LED Spots | LED Strip for Cupboards

 

How to Cut and Join a LED Strip

Buy LED Strips here, click

You can cut the LED strip at the points marked below. Depending on the type of LED strip there should be 3 LEDs per section. The LED strip I sell have 60 LEDs per metre, thus you can cut it at every 50mm and it will have 3 LEDs in 50mm. You do not have to cut it, you can even use a complete 5 meter roll as it is.

You can use normal scissors to cut the strip.

LED strip

After you cut it you must first remove the silicon layer before you can solder some wires onto the contact points.

Take a carpet knife and cut into the silicon layer. The white backing is rather hard so you do not have to be too worried that you will cut through the whole thing. If you cut too hard you will cut through it, but the backing is a copper circuit board so it is not that easy to cut through it.

Cut LED strip

Now you put the blade of the knife between the white backing and the silicon layer and peel off the silicon layer

Remove silicon layer on LED strip

Sometimes you will be lucky to cut it on a joint where there already is soldering (like in pictures 2 and 3 above), then you can just solder the wire ends to it. Sometimes you will have to cut it on non-soldered joints like in the first picture and then you have to follow the steps below.

Sometimes the silicon will come off nicely and sometimes it will also take the white layer off. Do not worry about that because if the white layer is off you are on the copper backing where you want to be. It will now look like the picture below. You can also turn it around and remove the double sided tape in the area where you will solder.

Make sure all the silicon has been removed from the area where you will be soldering.

LED strip

Some of the latest models I imported have small contact points. After you removed the silicon it is better to first scrape some of the white paint off Or use sand paper to remove the paint in order to open a wider contact area to solder on. See the next photograph.

LED strip

Clean LED Strip

Also note that on these new models the + and - signs are not on each cutting line anymore. If you bought a metre or more and you cut it into pieces yourself you must make sure there is a + and - Sign on the shorter piece, otherwise you have to make a mark yourself so that you know which side is which polarity.

Now add a drop of soldering on each of the points on the strip.

LED strip solder

Then add soldering to the open ends of the wire you will be attaching.

LED strip

Then it is easy, just put the wire on the solder drops on the strip and heat it a bit with the soldering iron, you will see that they fuse very easily.

LED strip wire

STOP: PLEASE NOTE: If you bought the 5050 LED strip with 4 contact points, see the end of this tutorial to see how you must solder it.

I bought myself some 6mm Heat Shrink. You can put the heat shrink over the area. This will not only isolate it, but also help to keep it stable so the joint do not come loose that easily.

LED strip

For those who do not know heat shrink, you put it over the joint loosely like in the pic above. Then you apply heat with a heat gun and it will shrink tightly around the wire and joint. You can also use the solder iron to apply heat to shrink it.

LED strip

OR

LED Strip heat shrink

If you bought the larger LED strip with 5mm LEDs (5050) you must attach the wire as follows:

You will note there are 4 contact points, GRB and +

You attach the positive wire to + and you have to bridge all three the other points to connect to the negative wire.

5050 LED strip

I cut the - wire longer than the +, then bend the - 90 degrees and let it go other all 3 negative points.

5mm LED strip

Why are there 3 contact points?

They use the 5050 strip for a RGB strip. This strip can change its colour. You will note that in each LED chip there are in fact 3 different small LEDs. In the case of the white LED strip they make all 3 internal LEDs white. If you want to be clever you can put each of the GRB wires on a different switch and decide how much light you need. Brighter, brighter and brightest.

Click here to buy a 5050 LED Strip

Using a Quick Connect fitting

If you use a quick connect fitting to join your LED strip you still have to remove the silicon layer and you still have to clean the contact points

The photographs below illustrate how to do it

Cut LED strip
Cut

Bend and peal
Bend and Peal silicon off

Clean LED strip

Join LED strip
Use 100 grid sand paper to remove the varnish layer from contact points

Quick connect fitting for LED strip

Other web sites owned by me: hilux4x4.co.za | photosa.co.za | digiprop.co.za | freeforex.net | freeonlineads.co.za | shareinvest.co.za | 4x4direct.co.za | bokkom.co.za | stilbaai.info | clivias.info | bmw-toruing.co.za | bmw-dakar.co.za | digicar.co.za

created by Pieter Pretorius